最新消息:20210816 当前crifan.com域名已被污染,为防止失联,请关注(页面右下角的)公众号

【已解决】HD Tune测试硬盘健康状况中:重定位扇区数量-衰退,重定位扇区数据操作数量-警告,如何解决

电脑知识 crifan 29707浏览 0评论

【问题】

硬盘用HD Tune Pro检查健康状况,结果是

重定位扇区数量 – 衰退

重定位扇区数据操作数量 – 警告

重定位扇区数量

现在想要搞懂,错误的具体含义是啥,以及如何解决此错误。

【解决过程】

1. 网上找了一堆,竟然没几个解释清楚的。

2.后来还是在

部分HD tune 测出重定位扇区数量警告,这个问题严重吗?多谢

中看到一些解释。

所以想到去试试英文版,找找其帮助手册,看看相关的解释是啥。

3. 所以去HD Tune主页中

http://www.hdtune.com/download.html

下载了HD Tune Pro

hdtunepro_500_trial.exe

对应的英文界面是:

Reallocated Sector Count

Reallocated Sector Count:

Number Of damaged sectors which have been replaced

 

Reallocated Event Count

Reallocated Event Count:

Number of sector replacement operations

 

注:我此处是SSD。

出错的硬盘是别人的。

所以上述界面仅供参考。

 

而关于上述界面中的“最差/Worst”一项,很容易让人理解为:

当前硬盘所允许的最差的值。但是很奇怪的是,其值和“当前/Current”,却多数时候都是一样的。

那岂不是变成,每一项都是达到了硬盘的最差情况了,那和硬盘的正常情况,完全相反。因为我的硬盘是很新的硬盘,完全是正常的才对的。

 

所以,对此问题,后来看到了英文版的HD Tune中手册的解释,才明白的:

This function uses S.M.A.R.T. (Self-Monitoring Analysis and Reporting Technology) to get
information about the health of the hard disk.
The table shows the following parameters:
ID: parameter which is being measured
Current: current value
Worst: the worst value which has been recorded since the hard disk was first used
Threshold: the value of any of the parameters should never get below the threshold
Data: shows the usable data which belongs to the ID
Status: status of the parameter (OK, warning  or failed)

即,Wosrt表示的意思是,有记录以来的,在硬盘使用过程中,最差的值。

所以此值如何和当前值一样,那就是很容易理解了。

当前的值,如果出问题了,那么和最差值也多数会是一样的了。

3.所以,再去搜SMART 05,找到一些解释。

直接全部摘录过来算了:

硬盘SMART参数(05,C5)与(C7)解惑

SMART参数(05,C5)

硬盘SMART参数中(05)是非常重要的一项,称为重新映射扇区计数(Reallocated Sectors Count),它直接表示硬盘是否已经出现了不良扇区。

以前的硬盘只要某磁道出现一个坏扇区,该磁道就算“坏磁道(Bad Track)”,修复时就整个磁道所有扇区一起“跳过(skipped)”。所以,坏磁道和坏扇区没有区别开,一起称为“坏道”。而现在的硬盘每个磁道划为数百上千个扇区,不能因为有一个坏扇区就丢掉整个磁道。再说硬盘在制造完成后本身就已有相当多的不良扇区(可能有成百上千之多),所以为了提高成品率,硬盘的设计容量是大于标称容量的,多余的那部分(用户不可见的)容量就是用来弥补“制造时已出现的”以及“以后使用时新增的”不良扇区的。这也是现代硬盘的一个自修复功能,只要这个功能在起作用,你就不会发现硬盘出现坏道,所以说“坏道”也是一个应该淘汰的老词了。

这一自修复功能的原理是:当硬盘的某扇区持续出现读/写/校验错误时,硬盘固件程序会将这个不良扇区的地址重定向到预先保留的某个备用扇区,这就称为重新映射扇区。此后这个不良扇区不会再被使用,这等于将这个不良扇区屏蔽了,所以这样的硬盘容量不会减少,在Windows常规检测中也不会发现坏扇区,只有从SMART参数中才能发现已经有不良扇区被替换。

完好的硬盘,(05)项的数据肯定为零,当前值远大于临界值。如果数据不为零就表示已经有不良扇区被“重映射”,被重映射的扇区增加,当前值就会下降。如果当前值下降到接近临界值,就说明备用扇区将用尽。

与(05)项相配合的参数还有(C5)。(C5)是当前待映射扇区计数(Current Pending Sector Count),这一参数的数据表示了“不稳定”的扇区数,即“等待被映射”的扇区数量。因为扇区仅仅读取错误并不会导致立即重映射,只有在写入失败时才会发生重映射。
所以,如果有扇区在读取时出现错误,(C5)就会有计数,表示有扇区不稳定。如果该扇区随后被读写成功,等待被映射的操作就会取消,(C5)的计数会下降。如果下一次对该扇区的写操作继续发生错误,就会产生重映射,然后(05)计数要增加,(C5)计数随之下降。如果以后长时间并未再对该扇区进行任何读写操作,那么(C5)的计数也会一直维持下去。

因此,当你的硬盘发现(05)参数有了数据量后,并不需要任何操作,只要注意以后的发展。如果(05)的数据量不大,也不再增长,那这块硬盘还可继续使用。若(05)的数据不断上升,说明硬盘已处于不稳定状态,应当立即备份数据,调换硬盘了。因为备用扇区一旦用尽,再有不良扇区就会真的出现坏道导致数据丢失。即使使用专门的工具把坏道隔离出来,也不能保证不再出现新的坏道,而且硬盘容量会明显减少。

由于不同硬盘的备用扇区数量并不相同,所以单看(05)的数据量并不能判断硬盘还可支持多长时间,还要注意(05)的当前值,即使(05)的数据量不大,但当前值下降很快,甚至接近临界值,也应果断调换硬盘。另外,有的硬盘(05)的数据量很大,但不再增长,而且当前值也下降很少,这样的硬盘最好也不要再使用,因为保留的备用扇区都是位于磁盘的尾部,大量使用保留扇区将大大增加磁头的寻道操作,使得读写效率下降,导致系统运行缓慢。

SMART参数(C7)

(C7)参数也是比较引人注意的,这个参数的数据累计了通过接口循环冗余校验(Interface Cyclic Redundancy Check,ICRC)发现的数据线传输错误。如果这个值不为0而且持续增长,表示硬盘控制器→数据线→硬盘接口出现错误,劣质的数据线、接口接触不良都可能导致此现象,并将导致数据传输速度下降,与硬盘本身倒关系不大。

唯一要了解的是,有些新硬盘的这一参数也有一定数据量,这并不表示硬盘有什么质量问题。因为(C7)参数的数据只会增长,不会归零。所以当你更换了数据线、清洁了接口后发现数据不再增长,即表示问题已解决。

4.后来又去查到了wiki中的资料:

S.M.A.R.T.

ID

Hex

Attribute name

Description

05

0x05

Reallocated Sectors Count

Count of reallocated sectors. When the hard drive finds a read/write/verification error, it marks that sector as "reallocated" and transfers data to a special reserved area (spare area). This process is also known as remapping, and reallocated sectors are called "remaps". The raw value normally represents a count of the bad sectors that have been found and remapped. Thus, the higher the attribute value, the more sectors the drive has had to reallocate. This allows a drive with bad sectors to continue operation; however, a drive which has had any reallocations at all is significantly more likely to fail in the near future.[2] While primarily used as a metric of the life expectancy of the drive, this number also affects performance. As the count of reallocated sectors increases, the read/write speed tends to become worse because the drive head is forced to seek to the reserved area whenever a remap is accessed. A workaround which will preserve drive speed at the expense of capacity is to create a disk partition over the region which contains remaps and instruct the operating system to not use that partition.

196

0xC4

Reallocation Event Count

Count of remap operations. The raw value of this attribute shows the total count of attempts to transfer data from reallocated sectors to a spare area. Both successful & unsuccessful attempts are counted.[28]

197

0xC5

Current Pending Sector Count

Count of "unstable" sectors (waiting to be remapped, because of read errors). If an unstable sector is subsequently read successfully, this value is decreased and the sector is not remapped. Read errors on a sector will not remap the sector (since it might be readable later); instead, the drive firmware should remember that the sector needs to be remapped, and remap it the next time it’s written.[29] However some drives will not immediately remap such sectors when written; instead the drive will first attempt to write to the problem sector and if the write operation is successful then the sector will be marked good. This is a serious shortcoming, for if such a drive contains marginal sectors that consistently fail only after some time has passed following a successful write operation, then the drive will never remap these problem sectors.

198

0xC6

Uncorrectable Sector Count or

Offline Uncorrectable or

Off-Line Scan Uncorrectable Sector Count[23]

The total count of uncorrectable errors when reading/writing a sector. A rise in the value of this attribute indicates defects of the disk surface and/or problems in the mechanical subsystem.

199

0xC7

UltraDMA CRC Error Count

The count of errors in data transfer via the interface cable as determined by ICRC (Interface Cyclic Redundancy Check).

 

【总结】

最开始的图中的那块硬盘就是:

C5 当前待重定位扇区数量  200 200:表示之前已经出现过数据错误的次数有200次了。后续并没有继续出错,因为如果出错,就变成被替换的扇区了,下面的05就增加1,此处就减去1了。

05 重定位扇区数量 119 119 140: 表示当前硬盘最多允许你坏140此,有140个备用扇区供你替换坏的扇区。而你当前已经坏了119个扇区,都已被替换掉了。

所以,结论是:

当前硬盘的确是快坏了。

因为一共140个备用扇区,你都坏了119个扇区,用掉了119个了。

并且另外还有200个扇区,出现过错误。

所以,看起来,以后很可能继续出错。

建议:如果硬盘本身没什么重要数据。倒也无所谓,可以继续用着。但是要有心理准备,万一哪天真的坏了,不能用了。对你也没影响。

如果硬盘里面有重要数据,那么需要尽快备份出你的数据。然后要么继续用这个快坏了的硬盘。要么直接换一块新硬盘。

转载请注明:在路上 » 【已解决】HD Tune测试硬盘健康状况中:重定位扇区数量-衰退,重定位扇区数据操作数量-警告,如何解决

发表我的评论
取消评论

表情

Hi,您需要填写昵称和邮箱!

  • 昵称 (必填)
  • 邮箱 (必填)
  • 网址

网友最新评论 (1)

  1. 对比本文图1"05 重定位扇区数量 119 119 140 642"; 图2:"05 英文 100 100 3 0" .感觉,图一的数据含义应该是:对于完好的硬盘,(05)项的数据肯定为零,当前值(100)远大于临界值(3); 而坏硬盘,当前值119已经小于阀值140了,数据为642表明已被重映射642个备用扇区
    ny10年前 (2014-05-10)回复
85 queries in 0.177 seconds, using 22.15MB memory